Parts index
We stock over 34 Series 1 & 2 spares
This section contains all the series 1 and 2 spares we keep. You might find them elsewhere (i.e. in the bodywork section) but this is a list of ALL the series 1 & 2 parts we keep.
WMBL0367
This remade rubber gasket fits between the frame and air scoop on Series 1 and 2 Lambretta scooters.... [more]
WMBL0402
This set of rubbers are to fit down the side of a Series 1 or 2 horn cast and also between the horn cast... [more]
WMBL0437
This is a set of remade floor strips to fit on the rear foot boards of a Series 1 or 2 Lambretta. They are made... [more]
WMBL0458
This is a pair of remade side panel badges for Series 1 and 2 125cc and 150cc machines.... [more]
WMBL0573
This is a remade stainless steel fits Series 1 and 2 bridge piece.... [more]
WMBL0630
This Italian made alloy clamp holds the legshield beading in place on a Series 2 scooter. It is used at the top and the bottom... [more]
WMBL0789
This plastic gem fits into the headset top of a Series 2 and is supposed to let you know your lights are on.... [more]
WMBL0872
This collar fits between your clutch lever housing and your headset bottom and acts like a shim. They do wear out over time so they... [more]
WMBL0976
This Italian remade steering lock fits Series 1 and 2 Lambrettas. It features the small flap to cover the lock. You get... [more]
WMBL1014
This set of rubbers fit between the legshields and the alloy floor runners used on Series 1 and 2 125cc models.... [more]
MBP0238
We were so disappointed with the variable quality of the toolbox lid hinge pins that MB made these in stainless steel. These only fit Series... [more]
WMBL1181
Rear light lens to suit Series 1 and 2 rear light units. The mount holes are offset, slightly above centre.... [more]
WMBL1182
Rear light lens to suit Rear lights originally from Aprila. The mount holes are offset, slightly below centre.... [more]
WMBL0518K
This kit of fasteners will secure your floorstrips to your legshields and then to you frame. It is for the 125cc models with the rifled... [more]
WMBL0869K
This handy kit contains all the stainless fasteners needed to attach your rear mudguard to your frame on any Series 1 or 2 Lambretta.... [more]
WMBL0871K
This handy kit contains all the stainless fasteners needed to attach your rear number plate holder to your frame on any Series 1 or... [more]
MBP0237K
This kit of fasteners will secure your floor strips to your legshields and then to you frame. It is for the 150cc models with the... [more]
WMBL1202
This remade horn grille suits late Li and TV Series 2 models.... [more]
WMBL1205
This is a high quality remade shield shaped horncast badge. It fits all Series 1 Scooters.... [more]
WMBL1194
These are remade Italian alloy channels to suit late type Series 2 legshields. They will require 6 rubber inserts.... [more]
MBFCUP4SS
Series 2 headlight rim cup washer and also universal fitting. ... [more]
WMBL1211K
Stainless steel horn cast fastener kit to suit Series 2.... [more]
WMBL1212K
Stainless steel headset fastener kit to suit Series 2 scooters.... [more]
WMBL1213K
Series 1 and 2 front mudguards fasten with these extra long screws not found any where else.... [more]
MBP0443
Handlebar (headset) throttle tube to suit a Series 1 and 2 in steel and chrome plated, MB... [more]
WMBP0553K
MB Headset (handlebar) throttle kit to suit Series 1/2 Li 125/150 models. This is a top quality precision kit made heavier to help reduce headset... [more]
WMBP0554K
MB Headset (handlebar) clutch kit to suit Series 1/2 Li 125/150 models. This is a top quality precision kit made heavier to help reduce headset... [more]
WMBL0875
This set contains the 2 bridge piece rubbers to suit a series 1 or 2 Lambretta. ... [more]
MRB0783
This is another Mark Broadhusrt design to allow the Koso round digital speedo or rev counters to fit into a Series 1 or 2... [more]